Original Posted By: Greg Bacon
Does anyone have a few yards of bias cut finish tape they don't need, preferably 3 or 4 inch?Thanks!-- Greg Bacon________________________________________________________________________________Date: Mon, 31 Oct 2011 11:20:39 -0500Subject: Re: Pietenpol-List: Polyfiber - bias cut finish tape
Pietenpol-List: Polyfiber - bias cut finish tape
Pietenpol-List: Polyfiber - bias cut finish tape
Original Posted By: Greg Bacon
Subject: Pietenpol-List: Polyfiber - bias cut finish tape
Subject: Pietenpol-List: Polyfiber - bias cut finish tape
Re: Pietenpol-List: Pietenpol Air Camper: One Person Injured In Plane
Original Posted By: norm
Re: Pietenpol-List: muffler packing
Original Posted By: Hans Van Der Voort
I'm building a small inline muffler in my exhaust system and wanted to hearopinions as to the best packing material for longevity.Douwe________________________________________________________________________________Subject: Re: Pietenpol-List: muffler packing
I'm building a small inline muffler in my exhaust system and wanted to hearopinions as to the best packing material for longevity.Douwe________________________________________________________________________________Subject: Re: Pietenpol-List: muffler packing
Original Posted By: Douwe Blumberg
Douwe,Check out burnsstainless.com lots of info on mufflershttp://www.burnsstainless.com/muffleraccessories.aspxPlus everything you need to make one yourself.Stainless steel "Scrubble" is best but not light.Glass mat is much lighter but you might have to repack a muffler once in a while.My next project will have glass mat and I plan for a repack every annual, if needed.My Pietenpol (Corvair) has no muffler, just 3-1 header pipe and 18" of exhaust pipe out to the bottom of the cowling.Exhaust noise is minimal for the pilot, prop and wind are worse.Exhaust noise for the poor suckers on the ground is a pleasant purr of a smooth 6.HansNX15KV-----Original Message-----
Douwe,Check out burnsstainless.com lots of info on mufflershttp://www.burnsstainless.com/muffleraccessories.aspxPlus everything you need to make one yourself.Stainless steel "Scrubble" is best but not light.Glass mat is much lighter but you might have to repack a muffler once in a while.My next project will have glass mat and I plan for a repack every annual, if needed.My Pietenpol (Corvair) has no muffler, just 3-1 header pipe and 18" of exhaust pipe out to the bottom of the cowling.Exhaust noise is minimal for the pilot, prop and wind are worse.Exhaust noise for the poor suckers on the ground is a pleasant purr of a smooth 6.HansNX15KV-----Original Message-----
Pietenpol-List: muffler packing
Original Posted By: Jim Ash
> Pietenpol-List: Polyfiber - bias cut finish tape
Original Posted By: airlion
>> Does anyone have a few yards of bias cut finish tape they don't need,> preferably 3 or 4 inch?>> Thanks!>> --> Greg Bacon>>> *>> " target=_blank rel=nofollow>http://www.matronics.com/Navigator?Pietenpol-List> =nofollow>http://forums.matronics.com> blank rel=nofollow>http://www.matronics.com/contribution> *>> *>> *>>-- Greg Bacon________________________________________________________________________________Date: Mon, 31 Oct 2011 09:28:20 -0700 (PDT)
>> Does anyone have a few yards of bias cut finish tape they don't need,> preferably 3 or 4 inch?>> Thanks!>> --> Greg Bacon>>> *>> " target=_blank rel=nofollow>http://www.matronics.com/Navigator?Pietenpol-List> =nofollow>http://forums.matronics.com> blank rel=nofollow>http://www.matronics.com/contribution> *>> *>> *>>-- Greg Bacon________________________________________________________________________________Date: Mon, 31 Oct 2011 09:28:20 -0700 (PDT)