Pietenpol-List: Local builders southern California

matronics · Post by **matronics** » Tue Jun 14, 2011 4:11 pm

Original Posted By: mark lee
Subject: Pietenpol-List: Local builders southern California

matronics · Post by **matronics** » Tue Jun 14, 2011 4:19 pm

Original Posted By: Ben Charvet

matronics · Post by **matronics** » Tue Jun 14, 2011 4:32 pm

Original Posted By: mark lee
Subject: Re: Pietenpol-List: Cables; control and brace

matronics · Post by **matronics** » Tue Jun 14, 2011 4:36 pm

Original Posted By: owner-pietenpol-list-server(at)matronics.com
I did the same as BenJack PhillipsNX899JP "Icarus Plummet"Smith Mountain Lake, Virginia _____

matronics · Post by **matronics** » Tue Jun 14, 2011 4:42 pm

Original Posted By: owner-pietenpol-list-server(at)matronics.com
Here's a picture:Jack PhillipsNX899JP "Icarus Plummet"Smith Mountain Lake, Virginia _____

matronics · Post by **matronics** » Tue Jun 14, 2011 5:47 pm

Original Posted By: Jim Boyer

matronics · Post by **matronics** » Tue Jun 14, 2011 5:50 pm

Original Posted By: Jim Boyer

matronics · Post by **matronics** » Tue Jun 14, 2011 5:51 pm

Original Posted By: Ben Charvet

matronics · Post by **matronics** » Tue Jun 14, 2011 6:12 pm

Original Posted By: shad bell

matronics · Post by **matronics** » Tue Jun 14, 2011 6:39 pm

Original Posted By: Michael Perez

matronics · Post by **matronics** » Tue Jun 14, 2011 6:41 pm

Original Posted By: Michael Perez

matronics · Post by **matronics** » Tue Jun 14, 2011 6:46 pm

Original Posted By: "Gboothe5"
And to add to Shad's comment: if you safety wire the motorcycle link it keeps theIAs happy. They don't even pause when they see it.--------Kevin "Axel" PurteeNX899KPAustin/Georgetown, TXRead this topic online here:http://forums.matronics.com/viewtopic.p ... __________

matronics · Post by **matronics** » Tue Jun 14, 2011 7:10 pm

Original Posted By: owner-pietenpol-list-server(at)matronics.com
Jim,Here=99s how I=99m doing the other end. I have since re-shaped the =98shackles=99 to a more slender look.Thimble wrapping.jpgGary

matronics · Post by **matronics** » Tue Jun 14, 2011 9:28 pm

Original Posted By: shad bell
When using the chain link it is advisable to use the AN-111 cable bushings instead of thimbles.See attached.Greg Cardinal ----- Original Message -----

matronics · Post by **matronics** » Tue Jun 14, 2011 9:59 pm

Original Posted By: shad bell
Here's a couple of mine. ----- Original Message -----

matronics · Post by **matronics** » Tue Jun 14, 2011 10:05 pm

Original Posted By: "Gboothe5"
I haven't done any research yet, but the A-65 is what I thought I might put upfront in my plane. Anyone have any advice?TomRead this topic online here:http://forums.matronics.com/viewtopic.p ... __________

matronics · Post by **matronics** » Tue Jun 14, 2011 10:17 pm

Original Posted By: owner-pietenpol-list-server(at)matronics.com
Dave,I hope you will join us next year for the 3rd annual West Coast PietGathering at Frazer Lake, near Gilroy..just a nice, short drive up 101.GaryCool, Ca.

matronics · Post by **matronics** » Tue Jun 14, 2011 10:21 pm

Original Posted By:
The A-65 is a very good match for the Air Camper. Especially in the lower elevations where you don't have to climb very high. It's reliability is legendary.Greg Cardinal----- Original Message -----

matronics · Post by **matronics** » Tue Jun 14, 2011 11:08 pm

Original Posted By: Jim Boyer

matronics · Post by **matronics** » Tue Jun 14, 2011 11:21 pm

Original Posted By: Jim Boyer

matronics · Post by **matronics** » Tue Jun 14, 2011 11:55 pm

Original Posted By: shad bell

matronics · Post by **matronics** » Wed Jun 15, 2011 10:37 pm

Original Posted By: Oscar Zuniga
Any tentative dates set for the 2012 Frazier Lake event yet?It's only about six hours south of me. Maybe a chance I canfly 41CC down there next spring, after I get the airplane ferriedup here to Oregon later this summer.Oscar ZunigaAir Camper NX41CC "Scout"Flying Squirrel N2069Z "Rocket"Medford, OR (soon to be Eagle Point, Oregon)website at http://www.flysquirrel.net ________________________________________________________________________________

matronics · Post by **matronics** » Thu Jun 16, 2011 7:29 am

Original Posted By: owner-pietenpol-list-server(at)matronics.com
Oscar,That's especially good news...hope it works out! Also, God willing, we willALL be treated to a first time appearance of Mike and Vic in their brand newPiet!Gary-----Original Message-----

matronics · Post by **matronics** » Thu Jun 16, 2011 8:06 am

Original Posted By: Dan Yocum

matronics · Post by **matronics** » Thu Jun 16, 2011 9:52 am

Original Posted By:> owner-pietenpol-list-server(at)matronics.com
Well we hope we can have it there. That's the plan anyway. We'll start fabricon the fuselage today! I think Gary can have his there next June too. What do you say Gary?Mike GroahSent from my iPhoneOn Jun 16, 2011, at 5:29 AM, "Gboothe5" wrote:> > Oscar,> > That's especially good news...hope it works out! Also, God willing, we will> ALL be treated to a first time appearance of Mike and Vic in their brand new> Piet!> > Gary> > -----Original Message-----

Brodhead Pietenpol Association